China Standardized Planetary Gearbox with 60mm Flange for NEMA Motor gearbox engine

Product Description

 

Merchandise Description

The reducer is typically used for lower-velocity and high-torque transmission gear. The motor, internal combustion motor or other large-speed managing energy is employed to attain the goal of deceleration by meshing with the large equipment on the output shaft via a gear with a little amount of teeth on the enter shaft of the reducer. The reducer will also have several pairs of gears with the very same theory to accomplish the perfect reduction result. The ratio of the quantity of tooth of the large and modest gears is the transmission ratio.
 

SPECIFICATIONS Stage RATIO RATED TORQUE (N.m)
PLF60-60mm Sq. FlangePlanetry Reducer  L1 4 25
five 28
7 20
ten 10
L2 16 30
twenty 30
25 32
28 30
35 30
forty 25
fifty 25
70 20
Adapted motor ∅ 8-14/ ∅38.1-2/∅F47.fourteen-M4
Rated Enter Speed (rpm) 1000/min
Max Enter Speed (rpm) 2000/min
Backlash L1 ≤10 Arcmin
L2 ≤15 Arcmin
Fault stop torque(N.m) 2 occasions of rated torque
Efficiency L1 96%
L2 94%
Average life span 20000h
Operating temperature -10°~+90°
Nosie  ≤60 db
Weight (kg) L1 0.seventy five
L2 1
IP 54
Installation strategy Any installation technique

 

Creation Variety

Here is our all items listing. If you would like to know CZPT sort of planetary gearbox, remember to CLICKING Photo to check out far more information.  

 

42 Collection Planetary Gearbox

Backlash: ten-15 arcmin

Ratio Assortment:

L1: 4,5,7,ten,

L2: 12,sixteen,20,25,28,35,forty,fifty,70

Frame Dimension: 42mm Input Flange

Gear Arrangement: Planetary Straight Tooth

sixty Collection Planetary Gearbox

Backlash: ten-fifteen arcmin

Ratio Variety:
L1: 4,5,7,10,
L2: 16,twenty,twenty five,28,35,forty,50,70
Frame Dimension: 60mm Enter Flange
Equipment Arrangement: Planetary Straight Enamel

ninety Sequence Planetary Gearbox

Backlash: 10-15 arcmin
Ratio Choice:
L1: 4,5,7,10,
L2: sixteen,twenty,25,28,35,forty,50,70
Frame Dimension: 90mm Enter Flange
Equipment Arrangement: Planetary Straight Enamel

Powder Metallic Series Planetary Gearbox

Backlash: ten-15 arcmin
Ratio Assortment:
L1: 4,5,7,ten,
L2: sixteen,twenty,twenty five,28,35,forty,50,70
Body Dimension: 42mm & 57mm
Equipment Arrangement: Planetary Straight Tooth

Correct Angle Series Planetary Gearbox

Backlash: 10-fifteen arcmin
Ratio Variety:
L1: 4,5,7,10,

L2: sixteen,twenty,twenty five,28,35,forty,50,70
Frame Dimension: 60mm & 90mm
Gear Arrangement: Planetary Straight Enamel

 

Software Subject

Automated Arms

 

Assembly Line

 

3D-Printer

 

Medical -Tools

 

CNC Device

 

Tapping Machine

 

Other Automation Products

 

Why Select Us

 

ZheJiang Substantial Precision Gear Transmission Co., Ltd

 

 

 

Company Profile

 

 

ZheJiang High Precision Gear Transmission Co., Ltd situated in HangZhou town, ZheJiang Province, China. It is a leading organization devoted in precision transmission components and program investigation, manufacture and product sales, different series of goods are manufactured in its 5000 square meters workshop, the precision planetary gearbox and gear motor are designed specially for photo voltaic strength market and have served a lot of large-scale solar assignments worldwidely. 

The analysis team has a lot more than 15 years ordeals in this field, who can guarantee a punctual and successful support to meet up with customer’s distinct needs. It has pasted the ISO9001 high quality management system and CE, items have been exported to lots of nations around the world with a vast range software in AGV, intelligent robot, logistic, industrial automation, photo voltaic vitality, vessel, packaging and textile and many others.Regularly, our objective is to promote the software of photo voltaic power market in the world, and we think it provides clear and sustainable vitality for humanity to much better defend our atmosphere.

Teams

Certifications

FAQ

 

Q1:Which places are your goods mainly utilised in?

A:At present, we have 2 principal goods: precision planetary gear reducer and photo voltaic geared motor. Most of the precision planetary reducers are utilised in automation fields, these kinds of as healthcare equipment, 3D printers, doorway openers, tapping equipment, CNC lathes and a series of automation tools. In addition, our solar geared motors are utilised in photovoltaic power generation tasks, which are mainly blended with rotary drives to drive solar panels to keep track of sunlight.
Q2: How to select the suited planetary gearbox?
A :First of all, we need to have you to be CZPT to provide appropriate parameters. If you have a motor drawing, it will allow us recommend a suitable gearbox for you more quickly. If not, we hope you can offer the subsequent motor parameters: output pace, output torque, voltage, current, IP, sound, functioning problems, motor dimension and electricity, and many others.
Q3: What is the cost ?
A : The primary figuring out aspect for the cost of every item is the buy quantity. You can talk with us and permit us comprehend every other. I imagine that our rates, item top quality and our providers can absolutely make you happy.

This fall: Do you supply personalized service?

A: Yes, we supply tailored providers. You only need to have to place ahead your demands, and we will do our ideal to offer you with a plan, make programs, and try out our best to fulfill your needs.

 

 

US $25-30
/ Piece
|
1 Piece

(Min. Order)

###

Application: Motor, Machinery, Marine, Agricultural Machinery, Laser Cutting Machine
Function: Distribution Power, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Vertical Type
Step: Double-Step

###

Samples:
US$ 30/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

###

SPECIFICATIONS STAGE RATIO RATED TORQUE (N.m)
PLF60-60mm Square FlangePlanetry Reducer  L1 4 25
5 28
7 20
10 10
L2 16 30
20 30
25 32
28 30
35 30
40 25
50 25
70 20
Adapted motor ∅ 8-14/ ∅38.1-2/∅F47.14-M4
Rated Input Speed (rpm) 1000/min
Max Input Speed (rpm) 2000/min
Backlash L1 ≤10 Arcmin
L2 ≤15 Arcmin
Fault stop torque(N.m) 2 times of rated torque
Efficiency L1 96%
L2 94%
Average life span 20000h
Operating temperature -10°~+90°
Nosie  ≤60 db
Weight (kg) L1 0.75
L2 1
IP 54
Installation method Any installation method
US $25-30
/ Piece
|
1 Piece

(Min. Order)

###

Application: Motor, Machinery, Marine, Agricultural Machinery, Laser Cutting Machine
Function: Distribution Power, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Vertical Type
Step: Double-Step

###

Samples:
US$ 30/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

###

SPECIFICATIONS STAGE RATIO RATED TORQUE (N.m)
PLF60-60mm Square FlangePlanetry Reducer  L1 4 25
5 28
7 20
10 10
L2 16 30
20 30
25 32
28 30
35 30
40 25
50 25
70 20
Adapted motor ∅ 8-14/ ∅38.1-2/∅F47.14-M4
Rated Input Speed (rpm) 1000/min
Max Input Speed (rpm) 2000/min
Backlash L1 ≤10 Arcmin
L2 ≤15 Arcmin
Fault stop torque(N.m) 2 times of rated torque
Efficiency L1 96%
L2 94%
Average life span 20000h
Operating temperature -10°~+90°
Nosie  ≤60 db
Weight (kg) L1 0.75
L2 1
IP 54
Installation method Any installation method

What Is a Gearbox?

A gearbox is the mechanical system of an automobile that allows a vehicle to change gear smoothly. This arrangement of gears is highly complex, which helps to provide a smooth gear change. In this article, we will explore some of the different types of gearboxes, including the Epicyclic gearbox, the Coaxial helical gearbox, and the Extruder helical gearing. These are three of the most common types of gearboxes used in automobiles.
gearbox

Gearboxes

Gearboxes help drivers choose the appropriate gear for the conditions. A lower gear produces the least speed, while a higher gear gives the maximum torque. The number of gears used in a gearbox varies to meet different demands on the road and load. Short gearing provides maximum torque, while tall gearing offers higher top speeds. These features combine to improve the driveability of a vehicle. But what is a gearbox?
The gearbox has a slew of components, including the bearings and seals. Among these components is the gearbox, which is subjected to wear and tear due to metal-to-metal contact. As a result, gearboxes require close monitoring. Various tests are used to assess the condition of gears, such as corrosion and wear. Proactive tests emphasize wear, contamination, and oil condition. However, there are also proactive tests, such as the ferrous density test and the AN test, which monitor additive depletion and abnormal wear.
The separating force is a key factor for the design of a gearbox. The primary radial measurement point should be oriented to monitor normal forces. The secondary measurement point should be located in the opposite direction of rotation from the primary radial measurement point. The separating force generated by a helical gear set is called tangential force. The primary and secondary radial measurement points should be positioned so as to provide information about both normal and tangential forces.
Manual gearboxes are often manual. The driver can control the synchromesh by using a selector rod. This rod moves the synchromesh to engage the gear. Reverse gears are not synchromesh because they are used only when the vehicle is at a standstill. In older cars, the first gear often lacked synchromesh due to cost or lack of torque. Drivers could still use first gear with a double-declutch.

Coaxial helical gearbox

The R series rigid tooth flank helical gearbox features high versatility and good combination. They have a wide range of motor power and allow for fine classification of transmission ratios. The R series gearbox has several advantages, including high efficiency, long service life, and low vibration. This series of gearbox can be combined with a wide range of reducers and variators. Its size and high performance makes it an ideal choice for applications that require maximum torque and load transfer.
The main feature of a helical gearbox is that it presents a fixed velocity ratio, even if the center gaps are not perfectly set. This is sometimes referred to as the fundamental rule of gearing. A helical gearbox is similar to paper spur gears in terms of radial pitch, since the shafts in the helical gearbox cross at an angle. The center gap of a helical gearbox is the same for both the left and right-handed counterparts.
The EP Series is another popular model of a Coaxial helical gearbox. This series has high torque and a maximum reduction ratio of 25.6:1. It is an ideal choice for the plastic industry, and CZPT offers an extensive range of models. Their center distance ranges from 112 mm to 450 mm. The EP Series has several models with different center distances. In addition to high torque and efficiency, this gearbox has low noise and vibration, and it is easy to assemble and disassemble.
Another type of Coaxial helical gearboxes is the planetary gearbox. They have a high efficiency and power density. Unlike coaxial helical gearboxes, planetary gearboxes have an axis on the same direction as the output shaft. They are easy to integrate into existing drive trains. In addition, they are compact and easy to integrate with existing drive trains. For servo applications, they are another great choice.
gearbox

Epicyclic gearbox

An epicyclic gearbox is a type of automatic gearbox used to drive cars. Its primary advantage is its compact design, and it is more reliable and efficient than manual gearboxes. It is comprised of a sun gear and two planetary gears, encased in a ring gear called the Annulus. This system is useful for drivers who need to shift gears frequently, as they will become tired if the gears are suddenly changed.
An epicyclic gearbox consists of three different types of gears: ring gear, sun gear, and annular ring gear. The ring gear is the outermost gear and has angular-cut teeth on its inner surface. It is used in conjunction with planetary gears to provide high-speed ratios to vehicles. The sun gear also reverses the direction of the output shaft. This helps reduce transmission error.
An epicyclic gearbox uses multiple planets to transfer power between the planets. This type of gearbox is lightweight and features a high power density. This gearbox has several benefits over a standard single-stage parallel axis gearbox, including multiple load paths, unequal load sharing, and phased meshing. Furthermore, epicyclic gearboxes require more complex transmission error optimisation than their counterparts, including more than one stage.
The objective of epicyclic gearbox research is to provide the lowest transmission error possible. The process includes an initial design and detailed specification. The system is defined by its load spectrum and required ratio. Deflections of the elastic mesh are calculated to understand their strength and how much energy the system can handle. Finally, micro-geometric corrections minimize transmission error. These improvements are crucial to the overall efficiency of an epicyclic gearbox.

Extruder helical gearing

The helix in an extruder helical gearing is fixed at an angle, enabling more interaction with the shaft in the same direction as it moves. As a result, the shaft and the bearing are in constant contact for a long period of time. Typically, extruder helical gearing is used in applications where there is low excitement, such as steel, rolling mills, conveyors, and the oil industry. The bevel gear train also plays a role in these applications.
The CZPT AEX extruder drive gear is specifically developed for this specific application. The gears are compact and lightweight and offer exceptional power density and a long service life. These extruder gears are highly reliable, and they can be used in a wide range of applications, including rubber processing, food production, and recycling plants. CZPT offers both standard and custom gearing for your extruder.
Another advantage of helical gearing is its versatility. Since the helical gearing teeth are inclined at a specific angle, they can be adjusted to meet the specific needs of a given application. These gears also have the advantage of eliminating noise and shock from straight teeth. Unlike other gearing types, they are able to achieve a wide range of loads, from small to large. These helical gears are very durable and are the best option for high-load applications.
In addition to this, asymmetric helical gears have increased flexibility, while asymmetrical helical gears have lower flexural stiffness. The ratio of teeth to the shaft has a positive effect on the strength of the gear. Furthermore, asymmetrical helical gears are easier to manufacture. But before you purchase your next extruder gear, make sure you know what you’re getting into.
gearbox

1 speed gearbox

CZPT Group Components produces the one speed gearbox. It has the potential to make cars more efficient and environmentally friendly. The gear ratio of a car’s drivetrain is crucial for reaching maximum power and speed. Typically, a one-speed gearbox delivers a maximum of 200 hp. But the speed at which a car can reach this power must be high to get the full benefit from the electric motor. So, how can a one-speed gearbox improve the speed and torque of a car?
A one-speed gearbox is a mechanical device used to switch between second and third gears. It can include multiple gear sets, such as a shared middle gear for switching between second and third gears. It can also have an intermediate gear set that represents a switchable gear in both partial transmissions. The invention also includes a mechanism that makes it easier to change gears. The patent claims are detailed below. A typical one-speed gearbox may include two parts.
Generally, a one-speed gearbox will have up to seven forward gears, with each of these corresponding to a different speed. A one-speed gearbox can have five different gear sets and five different gear levels. It can have synchronized gear sets or last-shelf gear sets. In either case, the gears are arranged in a way that maximizes their efficiency. If the gears are placed on opposite sides of a car, the transmission may be a two-speed one.
CZPT Transmission specializes in the production of high-speed gearboxes. The company’s Milltronics HBM110XT gearbox machine is the perfect tool for this job. This machine has a large working table and a heavy-duty load capacity, making it a versatile option for many kinds of applications. There are also a wide variety of CZPT gearboxes for the automotive industry.

China Standardized Planetary Gearbox with 60mm Flange for NEMA Motor     gearbox engineChina Standardized Planetary Gearbox with 60mm Flange for NEMA Motor     gearbox engine
editor by czh 2023-01-09